Thursday, March 7, 2013

WHY ENGINE LIGHT COMES ON


EPC LIGHT


Seeing a VW or a Volkswagen or Polo da Volkswagen or a VAG car or a new Polo on tow,  is becoming an all too familiar site, - view picture below. VW cars are seen piggy-backed and carried to service centers on a daily bases because VW owners are encountering serious trouble with their Volkswagen cars.  
Many Volkswagen drivers are often stranded on the high ways or freeways whilst driving to and from work because their VAG cars are throwing tantrums, by going into limp mode and turning on the EPC light.  Most VW drivers have no idea why engine light comes on. 

I've been late for  meetings on several occasions because of this. On a few others, I couldn't make it to the  bank in time because the Electronic Power Control -EPC- circuit incapacitated my VW Polo Classic 2.0L Highline. The worst was when I took my daughter to the dialysis clinic and the Electronic Power Control (EPC) light came on, because I ran over a speed bump a little too fast. This resulting in "Limp Mode" causing my daughter to be substantially late for her dialysis session. This could have been a life or death situation but fortunately it wasn't.

I took this photo with my cell phone. The picture quality really isn't good, so therefore the
Bluemotion badge 
to the left of the right side tail light  isn't clear at all.  But I couldn't pass-up
the opportunity to capture a 
VW Bluemotion 2012 loaded on a roll-back.

Anyway,  lets look at why this very risky and inconvenient issue haunts most VAG car owners. All Drive-by-Wire cars (since 2000) has an Electronic Power Control (EPC) light. The EPC dashboard warning lights are not exclusive to VW or VAG cars but affects most other new cars regardless of its manufacturer though the common denominator is Drive-by-Wire and an Engine Control Unit (ECU) often called the Powertrain Control Module (PCM) with an embedded microcontroller supplied by the same manufacturer.  EPC stands for Electronic Power Control which is controlled by the ECU (Engine Control Unit). In essence the Engine Control Unit (ECU) is a microcontroller with associated circuitry which control the sub-modules in the car, all connected together by either OBD II or CAN-Bus. Certain outputs from these sub-modules can activate the Electronic Power Control  circuit, especially if the reason for sending its signals to the ECU (Engine Control Unit)  could cause damage to the engine or is a danger to the passengers. For example, if the car runs out of oil, or if the emissions exceed the prescribed level, or  if  the car hits a speed bump a little to hard or if a brake bulb fails.

In the first case the oil level sensor will detect that the lack of oil in the crankcase and since there is a possibility the engine may seize-up, it sends a pulse train to the PCM to activate the Electronic Power Control (EPC), which cuts the power to the engine, making the car go into "Limp Mode" and switching on the EPC warning light. In the second case the lambda sensors on either side of the catalytic converter  will detect the fuel rich exhaust fumes and send a pulse train to the PCM to activate the Electronic Power Control (EPC), which cuts the power to the engine making the car go into "Limp Mode", thereby limiting carbon pollution and  and switch on the EPC indicator light (epc warning light) . In the third case the engine knock sensors will detect the suspension knock as the car hits the speed bump and will send a pulse train to the PCM to activate the Electronic Power Control (EPC), which cuts the power to the engine making the car go into "Limp Mode" and switch on the EPC dashboard light. In the fourth case, one of the Electronic Control Unit or Body Control Modules (BCM) sensor will sense that a brake light is open-circuit, send a pulse train to the PCM to activate the Electronic Power Control (EPC), which cuts the power to the engine  making the car go into "Limp Mode" because in that condition the car is not roadworthy. The EPC dashboard light is a very graphic demonstration that there is something amiss in you VAG that needs to be remedied.

There are several other sensors strewn throughout the car and many of them can have an effect on the Engine Control Unit (ECU) and cause the EPC light to come on. Sometimes when the EPC fault light comes on, it may be a spurious error, based on past driving cycles. A driving cycle is calculated from the time the engine starts and drives -which should be a min 5 minutes- until the engine is switched off. It could  take three drive cycles to clear a spurious error but if the fault persists it has to be diagnosed on a VAG-COM diagnostic tester.

Should you require more information on,  what is epc light, what is a epc light, vw epc warning light, vw epc code, epc on a vw, epc warning light vw, epc vw tiguan,  epc on jetta, epc light on, what is the epc light,   epc fault light, checkout epc-demystified.

Here are some Non  Volkswagen Websites I highly recommend,  
http://electroniques.blogspot.com
http://photojani.blogspot.com
http://expowp.blogspot.com