Showing posts with label audi A4. Show all posts
Showing posts with label audi A4. Show all posts

Wednesday, November 9, 2022

On-Board Diagnostics

ON-BOARD DIAGNOSTICS 

A few days ago I was driving behind a string of cars through Liesbeek Parkway when I was startled by several drivers repeatedly  hooting at an Audi A4 driving in front of them to get out of the way or change lane. The Audi A4 that was holding up the traffic had a Guateng registration plate and  my first impression was that its occupants got lost at the spaghetti junction fly-over, not knowing which off ramp to take.

However when these impatient hooting drivers finally overtook the Audi A4 and I got to drive behind it;  I then realized that the Audi A4 was in fact in Limp Mode. Its driver was attempting to get to the shoulder of the road from the centre lane and the traffic just wasn't easing up.

In my opinion, these impatient driver just weren't aware that when a vehicle goes into Limp Mode it cannot go any faster than it's already going even though its driver was flooring the accelerator pedal. And I may add that ignorance about Limp Mode is no excuse, because its been around since 1996.


Vehicle Delivery Services Salvaged Limp Mode car


DRIVER COURTESY

Driver courtesy is very important to bolster safe driving conditions for everyone but an education regarding Limp Mode would be considered far more important. When a car suddenly reduces speed after driving at normal speed, it could be one of several reasons; among which could be steering vibration due to a puncture. Or the vehicle ran out of fuel. Or the engine may have switched off due to a dead battery caused by either alternator issues or snapped fan belt. 

Or the engine may be overheating, or the driver heard a disturbing noise coming from the engine. Or it could be an electrical fault like a faulty fuel pump or an ignition system failure like a defective engine or transmission control unit. Or the driver could have fell ill behind the wheel, to mention but a few of the myriad of reasons why a vehicle could stall or it may have entered in Limp Mode. 

AUTOMATIC TRANSMISSIONS

The engines of cars with automatic transmissions can sometimes switch off mid travel for some obscure reason. The only option the driver has, is to pull off the road, bring the car to a halt, place it in park or neutral to restart the engine. I know of someone who shifted his automatic transmission into neutral when the engine cut out mid travel, restarted the car and shifted it back into drive. This caused his car to almost come to a stand-still instantly causing the wheels to screech as the engines inhibited the transmission.  This type of action can and probably will damage the transmission subject to the gearing system inside and should never be done. Unfortunately no On-board diagnostics makes provision to prevent this.

When an engine cuts out at say 100kph both the power steering and vacuum boosted brakes stops working, thereby making steering difficult and the braking inefficient. It is therefore best to pull off onto  the shoulder of the road and check what the problem is an remedy it before continuing on your journey.

ON-BOARD DIAGNOSTICS

On-Board Diagnostics does a pretty decent job of protecting the engine and transmission against damage by limiting  acceleration, keeping the engine revs to a maximum of 2000 (RPM) and speed to about 45kph - aka Limp ModeWhen Limp Mode is enabled, it may lock an automatic transmission  in low gear and even disable both heating and air conditioning. Yet keeping the engine running so that it can be driven to a repair shop.

However, as clever as an ECU is,  it doesn't do anything to alert the driver of the car that follows close behind. Considering tail lights, brake light, reverse lights and  indicators represents a language used by vehicle drivers for those  following behind, to indicate their driving intentions. This light language that's been around for the better part of the automotive industry's existence yet it still haven't come-up with an appropriate and safe warning sign/method for Limp Mode. 

LIMP MODE INDICATOR

To remedy this, car manufacturers could include flashing hazard lights or perhaps fit an LED Display with a scrolling message along the the rear window as an alert to tell the driver following behind that the car in front of it has gone into Limp Mode. Alternatively, electronics savvy car owners can fit their own aftermarket hack by identifying the switching output of the appropriate automotive  High Side Switch (HSS) responsible for protection and diagnostics inside the ECU when Limp Mode is enabled.

Automotive industry High-Side Switches /Drivers - Integrated Circuit 

This may not be as easy as it may seem or sounds because of the myriad of automotive chip manufactures, each pushing their our integrated circuits (ICs) running custom/propriety software, among which are Infineon Technologies AG,   Robert Bosch, Qualcomm, Renesas Electronics Corporation (Intersil), NXP Semiconductors,  STMicroelectronics, Texas Instruments, Intel and Microchip Technology Inc, etc.

However, most of these manufacturers produce Power Switches and incorporate Open Load Detection in their design so that they can perform open-circuit diagnosis on loads, such wiper motors, fans, head lamps, fuel pump, mirrors, actuators in general and LED lights while  the load is enabled or disabled. Open load diagnosis is probably the most important function of the software driven High-Side Switch (HSS) and Low-Side Switch when wired in a specific configuration which allows for currents from 5mA to more than 10A to be accurately detected.   

As such able to generate a hardware signal (Limp Mode signal) that can directly control the hardware without the participation of the microprocessor in the ECU. This output can be used to as either a digital High of Low (using CMOS inverter) to drive a LED display that flashes LIMP MODE..... LIMP MODE..... LIMP MODE.....



Friday, November 3, 2017

EPC ELECTRONIC POWER CONTROL

EPC ELECTRONIC POWER CONTROL Q & A

Common causes for EPC warning light illumination

Over the past few weeks numerous questions came pouring in, really fast and furious, most of them at a loss about the EPC light on their vehicles. Below are a few of the VW owner's questions, accompanied by my answers that may have solve their EPC light problems. However, the symptom they present may be similar to your car's symptoms but the cause may not be identical, so therefore the answer may not exactly fit your problem, but it could at least but you the right track. If  you suddenly see the yellow EPC dash board light illuminate on your Volkswagen, Polo, Golf, Kombie, Jetta, Passat etc. don’t panic. 

The EPC light is amer/orange because it's an informational /warning light, whereas a red dashboard light calls for immediate attention, for example when the the oil or water dashboard lights comes on. EPC stands for Electric Power Control (EPC), and  is a computerized ignition and engine management system that can alert you to a potential engine malfunction, as well as alert you to a variety of engine issues, though most of them are fairly simple to diagnose and repair. Bearing  in mind other systems such as stability  control and cruise control can also have an effect on the EPC system.

QUESTION:- 

My VW Golf VI 2010 model shakes when I accelerate, then it suddenly looses power and the EPC light illuminates. Can you please help. What could be the cause of this  and please tell me how to fix it.


ANSWER:-


Most VW engines have a flat-plane crank, meaning the inner two pistons move up and down together, in opposition to the two outer pistons, each providing 90 degree crank propulsion. When one of the cylinders are not doing their portion of the work, the crank is unbalanced and will cause the entire car to shake. This normally happens when either an injector or a coil on one of the cylinders is misfiring. Since the EPC circuit monitors the engine torque, it will illuminates the EPC light when it diagnoses that 25% of its torque is lost. By restoring the 25% torque by replacing the faulty component, either the coil or the injector by a process of elimination, the shaking will stop. 

Then again, I experience severe shaking on my Polo 2.0 one day, for some reason o the other, two blades of he radiator fan  snapped off and the centrifugal force of the two remaining blades shook my entire car really violently. Its the first time I experience something like that and at that moment in time I got such a fright, my heart was pounding in my throat.

_______________________________________________

QUESTION:-

I have a Golf Polo 2012 model that's been to the agents for regular diagnostic tests because its been more than a year that they've been trying to resolve the “EPC” light  problem.  The following items have been replaced but the light still comes on -
Ignition coil, Throttle Body, Accelerator pedal, Four injectors
Cambelt kit, RPM sensor .

ANSWER:- 

Since so many components have been replaced, I would suggest you upload a diagnostic scan so that I can analyse it because the above looks like guess work. There are so many things that can trigger the EPC, but don't replace anymore components until you've checked:-

1) The rubber hoses to the MAF for cracks,
2) Cleaned out the tar-like deposits in the throttle body,
3) Cleaned the idle speed control and butterfly valve with Wynn’s Throttle Body and Air Intake Cleaner, 
4) Performed a throttle body adaptation, 
5) Checked that the knock sensors are properly torqued,  
6) Checked for the correct spark gap on your spark plugs, 
7 Checked that your engine temperature coolant sensor works, 
8) Checked that your fuel cap seals properly, 
9) Checked that your fuel pump isn't noisy, because if it is, its probably pumping under the required pressure. 
10) Checked the wiring loom connecting to the pencil coils and the fuel injectors for intermittent contact. 

_______________________________________________


QUESTION:-


Please tell me why does my Polo's engine switches off while I'm driving? When I try to accelerate there's no power and when I looked at the dashboard, the  EPC Dashboard Warning Light is on. That's when I realize the engine is not running. But thereafter my Polo wouldn't restart, not until  it cooled for a while. Then my polo will then drive perfectly normal until the next time the EPC light comes on again.

ANSWER:-

This sounds very much like an  Engine Speed Sensor problem. Normally when they do go faulty the car will not start at all.  It is common for the EPC light to come on, by which time the engine died and after about 2 hours everything is back to normal. However its seems like your Polo's sensor is just starting to give trouble. This is a hall sensor, that generates a waveform whenever it senses the rotational magnetic pulse. But when it gets too hot, it starts to fail. I've had hall sensors located inside the distributor go faulty on Opel Kadett GSI due to engine heat in peak hour traffic but after it cools down, the Opel starts and drives normal.  It seems like hall sensors don't like heat.   
_______________________________________________

QUESTION:-

I had my Volkswagen cc R-Line's  brake pads replaced after 48,000 kilometers  but now every time when I accelerate the EPC light comes on and there's no power. I'm totally miserable because the car is now useless. Can you please shed any light on this matter?   


ANSWER:-

Dude, its more likely than not that you've picked up a wheel speed sensor problem from your mechanic. One of two things, either the plug to the ABS wheel sensor isn't making good contact / the wire from the sensor is broken off or the gap between the ABS sensor and the disk is wider than it should be. It's very unlikely that the sensors are faulty because it probably worked fine before your mechanic replaced the pads. A telltale sign is that your speedometer isn’t working because the front sensors are also the input for the speedo.

_______________________________________________


QUESTION:-


I was cruising on the freeway and suddenly the power just cut out and there was no more acceleration and the EPC light went on. I thaught my VW Jetta ran out of fuel because the fuel gauge was on empty but it didn't because I could still drive it slowly. but it wouldn't revv up.  I took it to the agents who said it was caused by driving with a little fuel in the tank. But now the same thing has happened to me four times thereafter. What can I do because the agents say there is nothing wrong.


ANSWER:-

If truth be told, your intank fuel pump must have overheated when you were driving with an empty tank. Remember the fuel pump is cooled and lubricated by the fuel in the tank and when there is no more fuel to cool and lubricate, the pump can overheat.  Also, if there is debris in the tank, it can block the filter or pipe attached to the pump. Since this is a low pressure pump  it won't have force to clear the debris and wont be able to feed fuel to the high pressure pump driven by the camshaft. It's probably best to have your fuel line cleared under pressure alternatively replace the fuel pump.

_______________________________________________


QUESTION:-

I have an Audi A4 with a early model 2.0T engine. For the past few weeks starting from cold in the morning has been a problem but since yesterday, it seems to have lost all power it power and the EPC light is on. With the pedal to the floor in any gear, the rpms increase but the car just won't pickup speed.  

That seem to a common issue with the older Audi A4 models. It's normally the high pressure fuel pump pawl that's busted, which probably destroyed the lobe on the camshaft as well. Sometimes the pressure of the camshaft hollows out and destroys the cylinder head. Check the high pressure at the output of high pressure pump, it it's low then  it's definitely the pump and camshaft combination.


Sunday, October 25, 2015

AUDI OIL PUMP PROBLEM

AUDI A4 ENGINE NOISE


For the past week my sister's Audi A4 2.0L 2007 has been having issues. When it starts its engine sounds like a tractor engine but after about 15 secs it quietens down and sounds and idles perfectly normal. Ever since its engine oil and oil filter change some seven weeks ago by her friend. The "Engine oil pressure light" keeps turning on, after some 20 minutes of driving, accompanied by a beep from the pizzo electric buzzer. Thereafter  it repeatedly  triggers  unexpectedly,  actually giving her a fright every time it does. I ran a scan with VCDS and there was absolutely no sign of engine trouble or DTC from the engine. Except for ABS signal out of specification fault which is totally unrelated to oil pressure. So since there was no problem other than the engine  Engine oil pressure light that triggered daily she decided to drive the Audi in that condition and tolerate the beeping. 

I inquired about the oil that they used, thinking perhaps that if the  grade of oil was too thick, it would affect the oil flow and pressure.  She fetched the container which still had some oil in it from the garage to show me what it was and on inspecting the viscosity of the oil between my thumb and forefinger I was amazed by the crap they sell unsuspecting customers. It turned out that she bought SAE 10W/20 oil at the local supermarket off the automotive shelf because it was going cheap. The oil was so thin, it was virtually like water, it couldn't even form a drop at the end of my finger. I even asked her if they mixed paraffin with the oil and she said no. I looked at the writing on the container to see if it wasn't two stoke oil for lawnmowers but it wasn't. 

Audi A4 Oil Pump (Old Top - New Bottom)
I then knew that this was the cause of the problem. The oil was too thin and the oil pump had difficulty in getting enough oil to the cams, bushes and gears  resulting in the noise caused by excessive friction during the the first 15 seconds when started. I actually thought that the oil may be too thick, so that the  oil pump couldn't push through the required volume of oil per minute. After telling her what an idiot she was to buy this cheap crap oil, I begged her to get some VW 50300 Long Life Engine Oil from the Audi agents.  I even offered to drain the crap oil out her Audi, flush the engine, replace the oil filter and fill it with the correct oil. The VW 50300 Long Life Engine Oil does cost a lot more than regular oil put it has the advantage of 30000 km before the next change. Fortunately it costs less than VW Automatic Transmission Fluid

So after replacing the filter and filling up with the new oil, the Audi now sounds a lot better but it is still noisy. Not as loud as it was before and the duration of the noise reduced from 15 seconds to about 4 seconds. Its  going to cost her a new oil pump replacement within the next week or so, because driving with a suspect oil pump is asking for the engine to seize and heaven alone knows what that's going to cost to repair.