Electronic Power Control

Electronic Power Control

What Does the Electronic Power Control (EPC) Warning Light Mean?

Traditionally hand brake, accelerator pedal, clutch and bonnet release, used some sort of cable system and the steering column and gear levers used several mechanical linkages. Today virtually all these mechanical systems have been replaced by electronics in the form of sensors, feeding computers and electric motors performing as actuators. The legacy accelerator cable that controlled the throttle valve and fuel supply in the trusty old carbureter has been entirely replaced by electronics. It is now referred to as drive-by-wire (drive the car by means of electric wire control) and the EPC circuit oversees drive-by-wire system.

So what is an EPC circuit?

EPC stands for Electronic Power Control (EPC) and is a sub circuit of the car's computerized engine management system better know as its ECU which stands for Electronic Control Unit or  Engine control Unit. The EPC circuit uses the input signal supplied by the accelerator position senders and  the throttle angle senders to calculates how much engine power the driver requires. The EPC system also receives input signals from other systems on the car, like the stability and cruise control systems and translates this data into engine torque by means of the actuators.

The EPC circuit also monitors these components at start up and whilst driving and should it detect any malfunction, it will readily illuminate the EPC warning light . The EPC light is a bright yellow/amber instrument cluster light displaying the letters EPC. But it's just a 'Indicator Symbol light' that  informs the driver that an issue occurred in the torque system. Some faults within the EPC circuit will more than likely disable other functions on your vehicle that may even cause it to go into limp mode and not rev or perform very sluggishly.

EPC Warning Light

Since the EPC is a sub circuit of the ECU which supervisors several other systems on the vehicle, it is likely that other warning lights my also illuminate  on the instrument cluster. For example the Check Engine Light (CEL) may illuminate to indicate that the engine itself isn’t operating at normal efficiency. At the same time the stability and cruise control will be disabled and their respective lights may turn on as well.  

When this happens, you will need to have your car scanned for diagnostic trouble codes (DTC) or you could do it yourself if you have an appropriate scanner. Once the error codes are identified, it would be relatively easy to repair / replace the component responsible, and thereafter clear the fault codes. The illuminated lights should all turn off and the car should once again drive as per normal.

Is it safe to drive with the EPC light on?

Many people inquire  whether or not it safe to drive with the EPC light on? In my humble opinion, I would say,  Yes it is safe to drive with the EPC light on, because the EPC light is an abler light and not a red light. Red lights dictates that you shouldn't  drive the car at all, until the problem causing the red light to illuminate is repaired. Whereas an amber light is just an information sign. One can equate dashboard lights to road signs, for example if a red traffic light or a red stop sign with white-background  or other red and white regulatory sign is blatantly disobeyed, it will more likely than not result in harm or injury. Round red and triangular red road signs are warning signs and means danger. Also any sign with a white background signifies the sign is permanent  whereas a sign with a yellow background signifies that the sign is temporary and any square /diamond shaped orange/amber signs are used for roadway works information and guidance.

So return to the subject at hand, yellow/amber lights are therefore informative and temporary. However when the EPC light is on and the car goes into limp mode then its not safe to drive with the EPC light on, because you will be going dead slow and be an obstruction to other motorists. Limp mode is just a shortened form for limp home mode which is  an operating mode set by the vehicle's on-board  computer which is pre-programmed by the manufacturer. This program limits  your vehicle throttle in order to protect the engine or the car itself or its occupants from harm or injury and the car should only be driven to take it for  repairs.

As can be seen, the four signs on the right are red with the top two including white
whereas the four signs on the left are all yellow  which is informative and temporary. 

However the severity of the EPC problem can vary greatly and the vehicle may not be operable at all.  Common cause of  car’s EPC circuit malfunctioning are its sensors. Replacement normally solves the problem, however EPC faults can register intermittently to the point of frustration. In such cases it's very likely the wiring harness are intermittently faulty especially where the plugs connect to the sensors. If your engine suddenly shuts off while driving, you may want to look at the Engine speed sensor. The  crank shaft rotation sensor also commonly fail, when starting the car's engine while stationary. A tell tale sin is that the  the engine switches off after two second of idling. 

The brake light switch is yet another  EPC light trigger and is solved by replacement. This switch is a double pole double trow switch and isn't physically associated with the brake other than the same switch is used. On automatic vehicles brake switch failure locks the gear lever in Park and prevents  from selecting any other gear. The Mass air flow sensor is another common cause of EPC problems but in many cases it's not the MAF itself. It may be due to minor cracks in the rubber hoses that causes air to be sucked in, upsetting ECU calculations. The Throttle body and its angle sensors and drive motor is another is also another EPC problem child.

@volkswagenindia why am I getting EPC light again and again. Already 7 times repaired. Tired!! @Volkswagen pic.twitter.com/S1GzM6shNT

— विरल (@Viral_HS1) July 1, 2017

My EPC light

My EPC light 

If you've had your VW, Audi, SKODA or SEAT for a while, you're probably familiar with the EPC light and already experienced its wrath. If you haven't encountered the EPC warning light as yet, then you are definitely one of the lucky ones, because I know of several VW Polo, Seat Ibiza,  VW Jetta, VW CC, Passat, Audi A3, Audi A6, Seat Leon and even Porsche owners with odometer readings as low as 1500 Kilometers, who got spooked by the EPC light when it first stuck.

This EPC light is known to trigger instant panic and fear in many VAG car owner, and I don't blame them, since it can be a scary and dangerous experience, especially when the car goes into limp mode when you're overtaking or the engine just dies when exiting a 

freeway  off-ramp or when entering a highway on-ramp during peak hour traffic.  

Electronic Power Control

However, if you have no idea what an EPC light or an EPC fault is, nor why this warning light turns on, then you should do yourself a solid and continue reading. In a nutshell, the EPC warning light is a standard feature in all ODB-II compliant models of Volkswagen, SEAT, SKODA and Audi vehicles. 

Most of them, are fitted with 'drive-by-wire' technology, though neither are exclusive to VAG cars. And when I say VAG cars, I also mean  Porsche, Bentley, Bugatti, Lamborghini and Ducati. Toyota, Honda, Ford, Mercedes also has it, in fact, virtually all cars manufactured post 1996  have an EPC warning light. EPC is an acronym for Electronic Power Control, and its a  warning light that resides inside the instrument cluster display.

EPC Light

Nonetheless, the EPC light is not all doom and gloom. It is there for a reason, and that reason is to safeguard the car and the engine from damage or destruction, especially considering what they cost to repair these days, let alone the cost to have an engine overhauled. Many people are under the misapprehension that the EPC light indicates an issue  with the cars  computerized system, whereas mechanics tend to echo that the EPC light indicates  a potential engine malfunction, though that's not strictly true either.  

MIL 

Before we continue, I just needed to add that when the engine malfunctions, it illuminates the Malfunction Indicator Lamp (MIL) aka Check engine light (CEL), which is indicative of  a computerized engine-management system malfunction. It even has an amber/orange icon of an engine, so as to draw your attention to the engine. Furthermore if this amber icon engine light is steadily illuminated, it indicates a minor engine fault but when it blinks it signifies a major engine fault. On the other hand, the EPC (Electronic Power Control) warning light  is a distinctly separate light from the MIL or CEL because it is related to a different function.

The more appropriate answer to 'What is an EPC light?' would be that the Electronic Power Control warning light, indicates a malfunction in your VW, Audi, SKODA or SEAT's  throttle control system, though once again that's also not totally accurate either.  So let me throw so light on the subject. The EPC light is in fact a diagnostic test light. So when the car's ignition is first switched on, the EPC light is illuminated for about three seconds. If there are no faults in the EPC system the light will automatically extinguish.

Drive by Wire

This three second time period is the duration of a self-diagnostic test. Effectively the Motronic ECM (J220) checks for malfunctions  in the Electronic Power Control (Torque system) accelerator system (drive-by-wire system), which includes the Throttle Body Drive Stepless Motor (G186) with its dual   independent Throttle Drive Angle Potentiometers (G187 & G188), the Accelerator Pedal Module with its dual independent Throttle Position Sensing Potentiometers (G79 &G185), the wiring harnesses that connects them all together and its associated sensor inputs from the Cruise Control  System, the Anti-lock Brake System (ABS), the Oxygen Sensor Control, the Automatic Transmission and the Air Conditioning System, etc. 

Charge Air Path

Here Air conditioning system mean all components involved in conditioning the air in the inlet manifold prior to combustion, implying the Throttle body / Mass Air Flow (MAF) sensor G70 and not A/C as in HVAC.  That being said, the functionality of an Electronic Throttle Control (drive-by-wire system) can regulate the Charge Air Path far more accurately than a physical cable between the accelerator pedal and the throttle valve. 

NonVolatile Memory

This being the case, by the time the EPC light illuminates on the dashboard  in response to some sensor detecting a problem  whilst driving, the problem already occurred.  The  EPC warning is just a way to tell you that there  was a glitch in the EPC (drive by wire system) and generally remains lit until the fault is cleared. The EPC light is known as K132 and is turned on by the Motronic ECM by providing the Ground  connection that keeps the light burning. At the same time, a DTC is registered and stored in non-volatile memory for later inspection.

Limp Mode

So the key piece of equipment to solving any EPC problem or issue is a diagnostic scanner. The fault below shows that the brake light switch F was the culprit that caused the EPC fault. Bearing in mind, that the Cruise control get its cancellation signal from the brake light when the brake pedal is depressed. When a brake light is fused or the dual contact brake switch goes open circuit and can't provide the requisite signal, the cruise control cannot be cancelled. The ECM detects this condition and construes it as a safety issue and sends the car into limp mode. 

Fault Codes

Essentially the EPC circuit prevented an accident from happening. Implying the brakes would work but the engine would still run at high rev set by the cruise control, meaning the brakes would be ineffective to bring the car to a stop. For safety reasons the EPC system closes the throttle valve to a predetermined position the brake pedal and the accelerator pedal are depressed simultaneously. However if the ECU detects that the brake was depressed before the accelerator, then acceleration will be carried out. 

1 Fault Found:
16955 - Brake Switch (F) 
P0571 - 35-10 - Implausible Signal - Intermittent

The fault below shows  that there is  an electrical malfunction in the Drive by Wire  circuit causing the EPC light to illuminate. After clearing the fault code, the EPC light just comes back on. The ECU was suspected and replaced but didn't solved the problem. It turned out that the  wiring harness between the ECU and the instrument cluster.

1 Fault Found:
18084 - EPC Warning Lamp (K132) Circuit: Electrical Malfunction 
P1676 - 35-00 - - 

The fault below  was on an Audi where signal from the Transmission  Control Module (TCM)  to the ECU was intermittent causing her to go into limp mode and idle really rough. Turned out that the TCM got wet from rain water that leaked into the carpets.  

1 Fault Found:
18265 - Load Signal: Error Message from ECU 
P1857 - 35-10 - - - Intermittent