Is EPC safe?

IS EPC SAFE?

The Electronic Power Control Circuit with its EPC light virtually has every motorist annoyed globally. Most motorists seem to be up in arms over this "idiotic warning light". Yes, this is exactly what several clients have called it because they believe manufacturers added it into cars as  a "cash cow" measure, which the dealer will reset by just pressing a button and charge then through there noses. This is really not the case because there are so many dealer's mechanical workshops that have no idea how to fault find nor repair and EPC fault. Motorists have even gone as far as saying the the EPC circuit is an unnecessary addition, as the tried and tested Otto Cycle internal combustion engine has worked perfectly for at least a hundred years without it.  

Without question, the EPC light is probably the most misunderstood dashboard light plaguing motorist the past two decades. However the EPC circuit is in fact a safety feature that few seem to appreciate. But is doesn't work in isolation, it is a sub circuit of a the ECU circuit. The ECU overseas the running of the running of engine at its peak whereas the EPC circuit is specific to the torque circuit - whatever propels the vehicle and safely stops the vehicle!

For example, in older cars that used a physical cable to control the throttle; it was prone to fray and could easily get stuck whist driving at high speed. This actually happened hundreds if not thousands of times, hence an alternative was imperative. When releasing the accelerator pedal with a frayed cable the engine would remain at a high rev and make braking difficult if not impossible. Restated, an accident in the making. This will never happen with cars fitted with EPC because it uses drive by wire - which in effect is an electronic throttle control,

Some Volkswagen vehicle problems makes driving in traffic very difficult let alone dangerous due to loss of braking & steering assistance. Case in point, when the ABS warning light comes on, its more often than not a melted fuse located on the battery cover that dies from metal fatigue or caused by faulty  or  intermittent connection on the wheel rotation sensor wiring.  Or if one of the brake light burns out, the EPC circuit would determine that the car is not in a "roadworthy condition" and instruct the ECU to disables propulsion so that the necessary repairs can be effected.

The EPC circuit monitors several sensors and when anyone of them go out of whack, the EPC kicks in, to the rescue of the driver by sending the car into limp mode. Admittedly not everyone shares the sentiment that "limp mode" is a safety measure because if appears to causes more feelings of frustration than feelings of safety. There are tens of thousands of motorists who would testify to the latter, myself included. I experienced  loss of power whilst driving on the freeway with a large trucks behind me, that almost wiped me out if I hadn't swerved out of its way just in time.

I'm almost certain you've had a similar experience with your Volkswagen. My sister had such an experience with her grandchildren in the car ad she swore she would never drive a Volkswagen again.

EPC ELECTRONIC POWER CONTROL

EPC ELECTRONIC POWER CONTROL Q & A

Common causes for EPC warning light illumination

Over the past few weeks numerous questions came pouring in, really fast and furious, most of them at a loss about the EPC light on their vehicles. Below are a few of the VW owner's questions, accompanied by my answers that may have solve their EPC light problems. However, the symptom they present may be similar to your car's symptoms but the cause may not be identical, so therefore the answer may not exactly fit your problem, but it could at least but you the right track. If  you suddenly see the yellow EPC dash board light illuminate on your Volkswagen, Polo, Golf, Kombie, Jetta, Passat etc. don’t panic. 

The EPC light is amer/orange because it's an informational /warning light, whereas a red dashboard light calls for immediate attention, for example when the the oil or water dashboard lights comes on. EPC stands for Electric Power Control (EPC), and  is a computerized ignition and engine management system that can alert you to a potential engine malfunction, as well as alert you to a variety of engine issues, though most of them are fairly simple to diagnose and repair. Bearing  in mind other systems such as stability  control and cruise control can also have an effect on the EPC system.

QUESTION:- 

My VW Golf VI 2010 model shakes when I accelerate, then it suddenly looses power and the EPC light illuminates. Can you please help. What could be the cause of this  and please tell me how to fix it.

ANSWER:-

Most VW engines have a flat-plane crank, meaning the inner two pistons move up and down together, in opposition to the two outer pistons, each providing 90 degree crank propulsion. When one of the cylinders are not doing their portion of the work, the crank is unbalanced and will cause the entire car to shake. This normally happens when either an injector or a coil on one of the cylinders is misfiring. Since the EPC circuit monitors the engine torque, it will illuminates the EPC light when it diagnoses that 25% of its torque is lost. By restoring the 25% torque by replacing the faulty component, either the coil or the injector by a process of elimination, the shaking will stop. 

Then again, I experience severe shaking on my Polo 2.0 one day, for some reason o the other, two blades of he radiator fan  snapped off and the centrifugal force of the two remaining blades shook my entire car really violently. Its the first time I experience something like that and at that moment in time I got such a fright, my heart was pounding in my throat.

_______________________________________________

QUESTION:-

I have a Golf Polo 2012 model that's been to the agents for regular diagnostic tests because its been more than a year that they've been trying to resolve the “EPC” light  problem.  The following items have been replaced but the light still comes on -
Ignition coil, Throttle Body, Accelerator pedal, Four injectors
Cambelt kit, RPM sensor .

ANSWER:- 

Since so many components have been replaced, I would suggest you upload a diagnostic scan so that I can analyse it because the above looks like guess work. There are so many things that can trigger the EPC, but don't replace anymore components until you've checked:-

1) The rubber hoses to the MAF for cracks,
2) Cleaned out the tar-like deposits in the throttle body,
3) Cleaned the idle speed control and butterfly valve with Wynn’s Throttle Body and Air Intake Cleaner, 
4) Performed a throttle body adaptation, 
5) Checked that the knock sensors are properly torqued,  
6) Checked for the correct spark gap on your spark plugs, 
7 Checked that your engine temperature coolant sensor works, 
8) Checked that your fuel cap seals properly, 
9) Checked that your fuel pump isn't noisy, because if it is, its probably pumping under the required pressure. 
10) Checked the wiring loom connecting to the pencil coils and the fuel injectors for intermittent contact. 

_______________________________________________

QUESTION:-

Please tell me why does my Polo's engine switches off while I'm driving? When I try to accelerate there's no power and when I looked at the dashboard, the  EPC Dashboard Warning Light is on. That's when I realize the engine is not running. But thereafter my Polo wouldn't restart, not until  it cooled for a while. Then my polo will then drive perfectly normal until the next time the EPC light comes on again.

ANSWER:-

This sounds very much like an  Engine Speed Sensor problem. Normally when they do go faulty the car will not start at all.  It is common for the EPC light to come on, by which time the engine died and after about 2 hours everything is back to normal. However its seems like your Polo's sensor is just starting to give trouble. This is a hall sensor, that generates a waveform whenever it senses the rotational magnetic pulse. But when it gets too hot, it starts to fail. I've had hall sensors located inside the distributor go faulty on Opel Kadett GSI due to engine heat in peak hour traffic but after it cools down, the Opel starts and drives normal.  It seems like hall sensors don't like heat.   

_______________________________________________

QUESTION:-

I had my Volkswagen cc R-Line's  brake pads replaced after 48,000 kilometers  but now every time when I accelerate the EPC light comes on and there's no power. I'm totally miserable because the car is now useless. Can you please shed any light on this matter?   

ANSWER:-

Dude, its more likely than not that you've picked up a wheel speed sensor problem from your mechanic. One of two things, either the plug to the ABS wheel sensor isn't making good contact / the wire from the sensor is broken off or the gap between the ABS sensor and the disk is wider than it should be. It's very unlikely that the sensors are faulty because it probably worked fine before your mechanic replaced the pads. A telltale sign is that your speedometer isn’t working because the front sensors are also the input for the speedo.

_______________________________________________

QUESTION:-

I was cruising on the freeway and suddenly the power just cut out and there was no more acceleration and the EPC light went on. I thaught my VW Jetta ran out of fuel because the fuel gauge was on empty but it didn't because I could still drive it slowly. but it wouldn't revv up.  I took it to the agents who said it was caused by driving with a little fuel in the tank. But now the same thing has happened to me four times thereafter. What can I do because the agents say there is nothing wrong.

ANSWER:-

If truth be told, your intank fuel pump must have overheated when you were driving with an empty tank. Remember the fuel pump is cooled and lubricated by the fuel in the tank and when there is no more fuel to cool and lubricate, the pump can overheat.  Also, if there is debris in the tank, it can block the filter or pipe attached to the pump. Since this is a low pressure pump  it won't have force to clear the debris and wont be able to feed fuel to the high pressure pump driven by the camshaft. It's probably best to have your fuel line cleared under pressure alternatively replace the fuel pump.

_______________________________________________

QUESTION:-

I have an Audi A4 with a early model 2.0T engine. For the past few weeks starting from cold in the morning has been a problem but since yesterday, it seems to have lost all power it power and the EPC light is on. With the pedal to the floor in any gear, the rpms increase but the car just won't pickup speed.  

That seem to a common issue with the older Audi A4 models. It's normally the high pressure fuel pump pawl that's busted, which probably destroyed the lobe on the camshaft as well. Sometimes the pressure of the camshaft hollows out and destroys the cylinder head. Check the high pressure at the output of high pressure pump, it it's low then  it's definitely the pump and camshaft combination.

Volkswagen and Audi EPC

Volkswagen and Audi EPC

The Internet is a huge repository of  information, some useful  and some not so useful, or more to the point, useless. But, there is so much of both, duplicated and reechoed  in posts like auto-facts, axleaddict, youfixcars, and motor forums by so many individuals. There is nothing worst than being led up the garden path by some ignoramus who knows squat about electro-mechanical engineering technology when you are desperately looking for answers. To reduce that from happening, I decides to bust some of the myths related to VAG cars that are being echoed over and over and over.

EPC can be a bitch to repair.

Myth 1
Here's the first myth from someone on Yahoo Answers, relating to a 2012 VW Polo. "You can clear fault codes by disconnecting your battery for a while".  And here's another, "just disconnect the battery on your Audi A3 for a little more than 10 seconds and your fault codes will be  gone"! 

Myth 1 Busted
Though the above is true for pre-1996 vehicles fitted with OBD-I, disconnecting the battery on any car manufactured post-1996 fitted with OBD-II will definitely not delete any fault codes because the ECU stores all DTC (Dignostic Trouble Codes) aka fault codes codes in its  non-volatile memory.  What it will do, is reset the cpu / timer. The term non-volatile memory is generally used for all types of solid state memory, meaning memory that doesn't need its contents refreshed periodically. 

However, the ECU also stores learnt values and basic settings, like for example the Fuel Control Learning Adaptation Values and the Kick-Down Position of the Accelerator which is needed by the automatic transmission. This data and your car's radio code is not stored in non-volatile memory and will undoubtedly be erased when the battery is disconnected.  Once the battery is reconnected, the adaptation process needs to be done which will enable the ECM to learn the new settings for the Drive-by-Wire electronic throttle  valve and store it. If you didn't save the radio code you have to go to a VW / Audi dealer with your VIN and they may be able to give it to you.

When you disconnect your car's battery, the ECU detects the loss of battery power and registers a DTC in the ECU's non-volatile memory to that effect. This record can be seen after the battery is reconnected and a  diagnostic scan is performed.  It would look something like this,

2 Faults Found:
00532 - Supply Voltage B+ 
            07-10 - Signal too Low - Intermittent

01598 - Drive Battery Voltage 
            07-10 - Signal too Low - Intermittent

Removing the negative terminal of the battery isn't all bad, it does have the advantage  of resetting  the system's ECU safety watchdog timer. A safety watchdog timer (WDT) is responsible for periodically generating a system reset in the event of a software glitch. This one of a kind CIC61508 safety watchdog timer is ASIL-D (Automotive Safety Integrity Level D) approved,  where level D refers to the highest classification of initial hazard against the risk of injury as defined within ISO26262 automotive industry standard.

Infineon Safety Watchdog timer 

Pressure Sensors

Myth 2
There are pressure sensor in the VW and Audi engine block that causes an EPC light to come on and make the car go into limp mode.

Myth 2 bustedYes, there are pressure sensors in both VW and Audi engines but they not fitted into the block and should not be mistaken for than for knock senors that are screwed to the block. Faulty or loose knock sensors can cause the EPC light to come on and send the car into limp mode.  The baro sensor measures the ambient air pressure and has a effect on engine performance altitude dependent.  The supercharger boost pressure is controlled via the regulating flap control unit Intake manifold pressure sensor/MAP sensor (MAP = Manifold Air Pressure) which can cause the EPC light to come on and send the car into limp mode. The high-pressure fuel pump delivers fuel at a pressure of up to 150 bar and any drop in this pressure can cause the EPC light to come on and send the car into limp mode. Common problem with loss of pressure is the fuel filter. Loss of oil pressure can cause the EPC light to come on and send the car into limp mode. Lastly there is high system pressure in the cooling system at high revs and sudden loss of this pressure can cause the EPC light to come on and send the car into limp mode.

Myth 3
EPC light usually means that the Electronic Throttle Body needs replacing and reprogramming.  

Myth 3 busted It is advantages to perform adaptation on the throttle body, before attempting to replace it with a new throttle body . Often times replacing it makes no difference and normally turn out to be the wiring harness connectors to the throttle body that's defective.   Disassemble the three electrical connectors around the throttle body clean  this inside of the connectors with circuit cleaner and reassembled. Also check for vacuum leaks, especially pressure regulator hose and the small pipes connected to the intake-manifold before replacing anything.

Myth 4
Epc light is mostly known to come on when there is emissions problems. 

Myth 4 busted This is incorrect because the 'check engine light' is specific to emission related problems, however The EPC light may also come on if the emission related problem affects the engine torque. So repairing the emission related problem first would in most cases reset both the EPC light and the 'check engine light'.

Sensors associated with EPC

Extensive safety measures have been designed and implimented 
in both the hardware and software of Audi and VW.  In most cases dual sensors are used for continual self-checking of signal plausibility. A safety watcg dog timer is integrated in the Motronic ECM to constantly and continually monitor the processor for correct and proper operation. Some of the sensors are listed below.

Fuel Pressure Sensor G247
Low Fuel Pressure Sensor G410
Oil Level Thermal Sensor G266
Heated Oxygen Sensor (HO2S) G39
Heated Oxygen Sensor (HO2S) 2 G108
Oxygen Sensor (O2S) G130 &  G130
situated behind 3 Way Catalytic Converter (TWC) G130
G186 Throttle Drive  (EPC))
G187 Throttle Drive Angle Sensor 1  (EPC))
G188 Throttle Drive Angle Sensor 2  (EPC))
Engine Speed (RPM) Sensor G28
Mass Air Flow (MAF) Sensor G70
Throttle Position (TP) Sensor G79
Accelerator Pedal Position Sensor 2 G185
Clutch Position Sensor G476
Throttle Valve Control Module J338 
Throttle Drive Angle Sensor 1 (EPC) G187
Throttle Drive Angle Sensor 2 (EPC) G188
Camshaft Position (CMP) Sensor G40
Camshaft Position (CMP) Sensor 2 G163
Engine Coolant Temperature (ECT) Sensor G62
Engine Coolant Temperature (ECT) Sensor G83 (on radiator) 
Knock Sensor (KS) 1 G61
Knock Sensor (KS) 2 G66
Brake Light Switch F

Automotive Electronic Components

Automotive Electronic Components

Admit it or not, we all love the new creature comforts of our modern day cars, all of which have become increasingly sophisticated.  Those seat warmers in the cold of winter, the climate control in mid summer, the air suspension on those bumpy roads, the infotainment systems with integrated GPS so that we never get lost again; and the on-board video player for those times we had to patiently sit and wait in our cars for our loved ones. ECU controlled fuel injection put an end to idling the car in the morning to get it to the appropriate operating temperature. Power steering and assisted parking makes both driving and parking a breeze. ABS and traction controls ensures that your car stops and corners without incident. 

Not to mention cruise control, the increased horsepower, the additional  safety features and the overall improved spatial comforts. And the list goes on. All of this was made possible by electronics, in the name of safety. Safety in the form of Safety Restraint Systems (SRS), Front and side airbags, early crash sensors and active front seat head restraints, to  mention but a few. 

On-Board Modules

Electronic engine management systems, carputer modules, telematic systems and other electrical components constitutes a sizeable percentage of our cars, collectively affording us the aforementioned comforts and conveniences. Besides, modern cars are loaded with code; and the number of electrical components in modern cars are on the rise, constantly and consistently increasing in number, and their failure can more often than not affect our driving safety. These electronic components can easily malfunction, either due to water ingress during wet weather conditions, or due to excessive vibration due to bad road surfaces, or just through general wear and tear. Most of these components are cheap and relatively easy to repair and replace but isolating the correct one can sometimes be trying. In a nutshell, modern day cars are seriously complicated, since they are not just computers on wheels but entire computer networks on wheels. Be that as it may, it is a well known fact that computers do crash, software have glitches and networks go off-line.

How safe is safe?

But, the million dollar question remains; are these electronic devices really safe or are they as safe as the car manufactures would like us to believe they are.  How safe is it when you're overtaking on a single lane highway at 100km per hour and the car goes into 'limp mode' or the engine just switches off and refuses to restart?  How safe is it when the steering wheel airbag explodes directly into your face for absolutely no reason? Its air pressure wave that's louder than a gun, is bound to temporarily deafen you and the smoke enveloping you would certainly disorientate you. These factors can contribute to you loosing control of the car through no fault of your own or even loose your life.  

How safe is it when you suddenly and momentarily loose steering control at high speed or whilst driving in fast moving traffic when your car doesn't react to your steering direction?  Or, how safe is it when your steering wheel suddenly goes stiff when turning (temporary loss of power steering)? How safe is it when your car randomly starts to jerk and switches off on a deserted road at night? 

How safe is your VW really, considering certain Jetta, Golf and Audi A3 models are being recalled for fuel leaks that can cause potential engine fires. Case in point, German supplier Continental Automotive GmbH has been supplying fuel tank polymer flanges that crack to five OEM parts supply companies at least 11 auto makers, VW, Audi and Porsche included.  What this means is that 
there are millions of cars of all makes and models that may have leaking fuel issues as we speak.

Electrical sub systems

As mentioned above, modern cars, can have as many as 200 small embedded electronic control units, better known as  (ECUs). Each module is in fact a fully fledged computer in its own right, overseeing one subsystem. Collectively they  have several functions, ranging from controlling the engine and or transmission, to controlling the immobilizer, to controlling the air bags, to unlocking doors, to controlling the radio, to managing the ABS, to managing the cruise control and such like. 

Most of these computer modules have input switches and or input sensors that can detect variables such as temperature, air pressure, braking, steering angle, voltages. All these computers are connected to a centrally networked  CAN bus that carries constantly varying data between them, in order to manage the car as it is being driven. The upside of this, is that the car can virtually drive itself but the downside is that when some essential module does go faulty, it would most likely shuts the car down which may also turn out to become an expensive repair.

Automakers are becoming more like 
assemblers and less like manufacturers

Essential components like headlights and spark plugs, ignition leads, wiring harnesses, relays and switches  can often be the first to go, but they are more electrical than electronic. Whereas the following list of sensors and actuators are totally electronic.

Air mass sensors (MAF) - electronic
Camshaft Position sensors - electronic
Crankshaft Position sensors - electronic
EGR Valves  - electronic
Knock sensors - electronic
Lambda (oxygen) sensors  - electronic
Throttle position sensors  - electronic
Wheel speed sensors  - electronic
Ignition Coils  - electronic
Glow Plugs  - electronic
Coolant temperature sensors  - electronic
ABS  actuators  - electronic
Injection valves - electronic
Solenoid valves - electronic
Anti-theft alarm  - electronic ... and the list goes on.

Since Automobile production requires several thousands of parts, most of these parts are not manufactured by the car maker but are supplied by auto suppliers. Hence automakers are becoming more like assemblers and less like manufacturers because Auto Megasupplier's  contributions have drastically increased from about 60% in the mid '90s to above 85% in 2017.  Among these auto megasuppliers are companies like:-

Robert Bosch supplies (Gasoline and diesel systems, chassis system controls, electronics,  exhaust gas turbochargers, steering systems, starter motors and alternators,   etc), 

Draexlmaier Group (wiring harnesses,  interior systems, cockpit and door modules, etc.),

Royal Philips Electronics (Lighting, car radio integrated circuits, liquid crystal displays, etc.)

Infineon Technologies (Microcontrollers, intelligent sensors; power semiconductors, etc.)  

Hella ( Electronic & lighting components, etc.)

DuPont Automotive (polymers, elastomers, specialty chemicals, lubricants, refrigerants, etc.) 

SKF Automotive ( Bearings, seals, clutch assemblies, SKF Automotive drive-by-wire systems, etc.) 

Valeo SA (transmissions, Micro hybrid systems, etc.)  

Magneti Marelli (Lighting, powertrain transmissions, electronics, suspension systems,  shock absorbers, exhaust systems, plastic parts, etc.)

Continental AG (Instrumentation, stability management systems, chassis systems, safety system electronics, telematics, powertrain electronics, interior modules, etc.) 

Eberspaecher Holding GmbH (Silencers, catalytic converters, particulate filters, manifolds, vehicle heaters, electrical vehicle heaters, electronics, climate control systems, etc.)

CITIC Dicastal Co.  (Aluminum alloy wheels, aluminum casting parts, etc.)

Mobis North America (Chassis, cockpit & front-end modules; ABS, ESC, MDPS, airbags,  LED lamps, ASV parts, sensors, electronic control systems, hybrid car powertrains, parts & power control units, etc.)

That being said, there are so many of these components from auto suppliers that are troublesome. For example, batteries, starter solenoids, diodes and alternator voltage regulators and relays. Considering that the alternator is the heart of  your vehicle's electrical system and that the electrical load has substantially increased due to the glut of extra electronics, I would think that some manufactures would at least have a second alternator for redundancy. Even perhaps a redundant network so that an alternative data path is  available if the wiring harness goes faulty. Or even dual temperature sensors, or dual camshaft sensors, etc. It would do marvels for reliability.

Volkswagen is recalling some 766,000 cars globally for a software upgrade to their "anti-lock braking system".

Volkswagen is recalling 8.5 million diesel cars across the European Union  due to the "emissions scandal".

Volkswagen is recalling some 90,000  gasoline powered VW Beetle, VW Golf, VW Jetta and VW Passat with 1.8T or 2.0T engines sold between 2015-2016, because the rear camshaft lobe has the tendancy to unexpectedly snap-off from the camshaft resulting in "loss of vacuum to the brake booster", implying inefficient braking and an increased risk of a crash.

Volkswagen recalls some 280,000 cars for fuel leaks.

Honda recently recalled 1.2 million  from the 2013-2016 model Accords years, citing 'faulty battery sensors'.


Ford South Africa recalled 2.0-litre diesel-powered Kuga SUVs to resolve a potential "brake problem". 

VW electric fuel pump

VW electric fuel pump 

VW electric fuel pumps are troublesome and VW, Audi, Seat and Skoda cars are notorious for fuel pump problems. Fuel pump problems commonly affect the Volkswagen Polo Classic 6n, the VW Polo 9N, the VW Bora, the VW Passat, the VW Sharan, the VW Caddy, the VW Golf, the Volkswagen Touareg  and the  VW Beetle, among several other. Its effects can range from intermittent no starting to stalling whilst driving, though most clients would complaint that the car jerks and stall and then just shuts off. However it's not always the fuel pump that's to blame. 

VW fuel pump relay

The VW fuel pump relay is another culprit that goes faulty or rather its external contact terminals tend to burn. So if your car wont start, give the Fuel Pump Relay #409 (1J0 906 383 C) or #410 (6N0 906 383A) a knock or two with a screwdriver handle and should the car start, then it's most likely a bad contact on one of its 7 spade terminal. Remove the relay and see if any of its terminal pins have burnt brown. If not, the relay's internal contacts are probably faulty and needs to be replaced. One consolation is that the relay is fairly cheap and it can be bought on-line at ebay.com for as little as $15. However, a VW fuel pump price on the other hand, is ridiculously priced especially  considering I've had a clients who had to have two fuel pumps replaced in under 9000 km. I don't think they are quality pumps.

When our VW Caddy's fuel pump started to give-in, it presented itself as an occasional engine misfire when pulling away from a stop street or traffic lights. The engine misfire became progressively worse over time, so it was booked-in for a service, for spark plug replacement, oil drain and oil  filter replacement, etc.  At this time we didn't know that the engine misfire was caused by the fuel pump. The day the Caddy was returned, it drove fine for the first two hours then started to misfire as it did before, but thereafter the fuel pump started sounding like a hoover vacuum cleaner. 

I knew it was the fuel pump because I've heard this sound before on both a Polo 1.4 Trendline and a Jetta 1.8 which at the time turned out to be the fuel pump. Anyway, the noise from the fuel pump was really high pitched and annoying, After several hours of driving it became unbearable so the Caddy went back to the mechanic who then diagnosed the fuel pump as faulty. After the fuel pump was replaced the noise disappeared and the miss was gone as well. My friend also  encountered the "hoover vacuum cleaner" with his Caddy but after a few days it just disappeared, so now he occasionally experiences starting problems.

VW  Fuel Pump Relay 409 / 410

VW  Fuel Pump Relay Part # 1J0906383B (409) is a 12V 40A relay with 7 spade terminal connectors, 2 Wide, 2 Standard and 3 mini. The same relay is  installed in VW Polo Mk3, VW Jetta, VW Golf Mk4, VW bora,VW beetle, Audi A3, Audi  TT, Seat Leon,  Skoda Octavia,  VW Sharan and VW Passat, etc.


VW  Fuel Pump Relay Part # 6N0906383A (410) is installed in VW Polo 6N, VW Golf Mk4, VW Lupo 6X, Skoda Fabia 6Y, VW Sharan 7M, AUDI A2, SEAT Arosa, SEAT Alhambra, VW Golf GTI, VW Passat and VW Polo Mk3, etc.

Replacing a fuel pump

Remember that the VW electric fuel pump relies on fuel passing through it for both cooling and lubrication. If or when running the fuel pump dry, fuel starvation can accelerate  internal component wear and may cause  the fuel pump motor to overheat and burn out. Electric fuel pumps run from the moment the ignition is switched on, so its fairly obvious that after a few years of operation their armature bushings, gears, commutator and brushes will suffer wear and tear, causing a gradual loss of pressure. Loss of fuel pump pressure commonly causes the "EPC" light to come on. A fuel leak or an Evaporative Emission System (EVAP) leak would also turn on the "EPC" light as well as the "Check Engine" light because the low inlet manifold pressure would upset the engine's air-fuel ratio and degrade engine performance and reduce fuel efficiency.  It would also diminish  power and acceleration, and possibly even cause stalling.  So if you need to replace your VW electric fuel pump, make absolutely sure you depressurize the fuel system before disconnecting the fuel lines. The easiest way to do this is to remove the fuel cap, remove the electric fuel pump fuse or relay and crank the engine a few times. 

Faulty Fuel Pump Flanges

There is currently a VW / Audi fuel pump recall, though its not necessarily the pump that's defective but rather faulty flanges manufactured by German supplier Continental Automotive GmbH. Apparently they've been supplying VW, Audi and Porsche with flanges that seem to crack and cause fuel leaks and potential fires. Apparently Continental sold the potentially faulty flanges to eleven automobile manufacturers and five OEM parts supply companies. Audi, Ford,  Fiat Chrysler, General Motors,  Jaguar-Land Rover, Lamborghini, Mercedes-Benz, McLaren, Porsche, Volvo and VW are just some of the automakers who used these industry-standard polymer flanges but other automakers may possibly also be at risk. 

Meanwhile Volkswagen, Porsche and Audi already recalled nearly a half-million vehicles because of leaky flanges, that cover fuel tank openings and is used for the fuel pump and other items. U.S. safety regulators are currently trying to track down gas tank flanges that may crack and cause fuel leaks on what could be millions of cars of all makes and models.

Continental Automotive GmbH supplied millions of fuel pump flanges to 11 car makers that can cause a potential fire. Is you car one of them?

— Faried (@Syba_seca) July 10, 2017